Internet Bonsai Club
Would you like to react to this message? Create an account in a few clicks or log in to continue.

Deadwood mold

3 posters

Go down

Deadwood mold Empty Deadwood mold

Post  Tona Thu Jul 28, 2011 1:17 am

I am new to the forum and have a juniper that has deadwood (shari) along the front down to the soil. There is green algae/mold just above the soil level. What is the best way to treat this. I think it is compromising the deadwood. You can see the dark area at the bottom of the deadwood. The soil mix is 30% pumice, 30% turface, 15% pine bark and 15% cactus mix. I live in a hot area where summer temps. are 100 degrees most days. That is why I do add some organic to the mix.
Tona

Deadwood mold 01311


Last edited by Tona on Thu Jul 28, 2011 1:19 am; edited 2 times in total (Reason for editing : Soil type)
Tona
Tona
Member


Back to top Go down

Deadwood mold Empty Re: Deadwood mold

Post  JimLewis Thu Jul 28, 2011 5:52 pm

Hard to escape that in areas where deadwood meets the soil.

You might try . . .

When you next repot, clean off the area, then use lime sulfur, followed when that has dried with Minwax Wood Hardener liberally at and below the soil level. This may require that you lift off an inch of soil a day or two before you repot to let the lower area of deadwood dry out so you can apply the lime sulfur and then wood hardener. It also will require to to heel the plant into some moist soil for an hour or two after you apply the wood hardener to let it dry before finishing the repotting.
JimLewis
JimLewis
Member


Back to top Go down

Deadwood mold Empty Re: Deadwood mold

Post  Tona Thu Jul 28, 2011 9:47 pm

Thanks Jim,
I will give the min-wax a try. I may be re-potting in late summer/early fall.
Tona
Tona
Tona
Member


Back to top Go down

Deadwood mold Empty Re: Deadwood mold

Post  Rob Kempinski Fri Jul 29, 2011 6:31 pm

Wet dry cycles really accelerate wood rot - the fungus that makes the wood spalted loves it. At the soil level the tree stays mostly wet but then dries, then quickly wet which will ruin juniper deadwood. The best thing is to remove the wet wood with carving tools (think like a dentist), dry it with a hair dryer and let it sit a day or two to fully dry and then put some sort of preservative on it. Personally I haven't had much success with MinWax wood hardener. I have recently switched to Rot Doctor - a very strong but effective wood preservative. If you have to, you can build up the dead section with some sort of epoxy, things like Bondo, material used to fix car dents, plumber's epoxy, I've even seen cement used (see photo below) or what ever you can find. It takes some work to make it look natural (and it may never look totally natural - kind a of like a tooth filling) and it will not be totally permanent but it will keep the water off the dry wood underneath and make the good wood last longer. The key is to get the wood as dry as possible prior to working on it with the chemicals. If that doesn't work then do what software developers do and make a bug a feature in the design. albino

Sorry for the lousy photo but the rotted bottom section of this tree belonging to a friend of mine was built up with cement. There is a much better shot of it in the First US National Exhibition Photo Album.
Deadwood mold Bci_2010
Rob Kempinski
Rob Kempinski
Member


Back to top Go down

Deadwood mold Empty Re: Deadwood mold

Post  Tona Sat Jul 30, 2011 5:16 pm

Thanks Rob,
This area of the trunk is a bit deeper than the deadwood area above it due to bad wood being removed. The possibility of using a "filler" is a good idea. I have a meeting with my Bonsai club next week. There are a few seasoned Bonsai enthusiasts that I am going to ask about this also.
Tona
Tona
Tona
Member


Back to top Go down

Deadwood mold Empty Re: Deadwood mold

Post  Sponsored content


Sponsored content


Back to top Go down

Back to top

- Similar topics

 
Permissions in this forum:
You cannot reply to topics in this forum